SKU:RB-05L007A LCD12864液晶摇杆扩展板
来自ALSROBOT WiKi
目录 |
产品概述
奥松机器人推出的LCD 12864液晶摇杆扩展板采用全新12864G-0088液晶屏为主体显示器件。此扩展板采用Arduino叠层板设计理念，可直接插接到Arduino UNO、Arduino mega328、Arduino mega2560、Arduino ADK控制器上使用，可以清晰显示中文、英文、字符、图片等；板上添加五向微型摇杆，方便实现人机互动；同时本板还具有5个模拟扩展接口和8个字扩展接口；其中各数字接口均分别用黑色、红色、黄色排针来区别电源地、电源正极和信号IO管脚；即方便操作又具有防呆的作用；而且扩展接口可连接各种传感器模块，如温度湿度传感器、三轴加速度计等，是制作显示互动作品不可获缺的显示器。
规格参数
- 产品名称：LCD12864液晶摇杆扩展版
- 产品货号：RB-05L007A
- 工作电压：3.3V
- 点阵：128x64
- 视窗尺寸：39.8mm x25.5mm
- 显示颜色：白色背光黑色文字
- 工作温度：0°C～+85°C
- 数据类型：数字输入
- 尺寸：70mm x 53mm
接口定义
- S：信号接口
- V：电源正极
- G/GND：电源地
- RST：同Arduino复位接口
- 3V3：同Arduino 3.3V接口
- VCC：同Arduino 5V接口
- VIN：同Arduino VIN接口
使用方法
连接示意图
如图所示，将12864液晶摇杆扩展板与 Arduino 控制器连接在一起
例子程序
#define cs_mini12864 2 //片选 低电平片选
#define rst_mini12864 3 //物理重置.低电平有效
#define rs_mini12864 4 //寄存器选择 1:数据寄存器 0:指令寄存器
#define sck_mini12864 5 //时钟
#define sda_mini12864 6 //数据
//上面的脚可以自己修改
#define Display 0xAF //显示开启
#define Power 0x2F //电源全开
#define VO 0x24 //对比度调节
#define AllPoint 0xA4 //非全屏显示
#define ADCset 0xA1 //负向，131-4
#define COMset 0xc0 //com0-com63
#define ELECTVO 0x81 //亮度调节 调节颜色 不同的模块需要不同的 ELECTSET
#define ELECTSET 0x2a //亮度数值 调节颜色 不同的模块需要不同的 数值
#define BIASSET 0xA2 //占空比1/9
unsigned char ao[]={0x00,0x00,0xFC,0x04,0x54,0xE6,0x45,0xF4,0x44,0xE4,0x54,0x04,0xFC,0x00,0x00,0x00,
0x88,0x88,0x4B,0x48,0x29,0x28,0x18,0x0D,0x18,0x28,0x29,0x48,0x4B,0x88,0x88,0x00};/*"奥",0*/
unsigned char song[]={0x10,0x10,0xD0,0xFF,0x90,0x10,0x80,0x60,0x1E,0x00,0xE0,0x07,0x18,0x60,0x80,0x00,
0x04,0x03,0x00,0xFF,0x00,0x03,0x20,0x70,0x2C,0x23,0x20,0x20,0x24,0x38,0x60,0x00};/*"松",1*/
unsigned char ji[]={0x10,0x10,0xD0,0xFF,0x90,0x10,0x00,0xFE,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,
0x04,0x03,0x00,0xFF,0x00,0x83,0x60,0x1F,0x00,0x00,0x00,0x3F,0x40,0x40,0x78,0x00};/*"机",2*/
unsigned char qi[]={0x80,0x80,0x9E,0x92,0x92,0x92,0x9E,0xE0,0x80,0x9E,0xB2,0xD2,0x92,0x9E,0x80,0x00,
0x08,0x08,0xF4,0x94,0x92,0x92,0xF1,0x00,0x01,0xF2,0x92,0x94,0x94,0xF8,0x08,0x00};/*"器",3*/
unsigned char ren[]={0x00,0x00,0x00,0x00,0x00,0x00,0xC0,0x3F,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x80,0x40,0x20,0x10,0x0C,0x03,0x00,0x00,0x00,0x03,0x0C,0x10,0x20,0x40,0x80,0x00};/*"人",4*/
void send_8bit_mini12864(unsigned char d) //传8位数据,高位先传
{
for(int i=0;i<8;i++) //循环8次,每次发送1个最高位
{
digitalWrite(sck_mini12864,0); //时钟拉低,一位数据开始
if(d&0x80) //与上10000000,最高位如果是1,就数据位就高
digitalWrite(sda_mini12864,1);
else //与上10000000,最高位如果是0,就数据位就低
digitalWrite(sda_mini12864,0);
digitalWrite(sck_mini12864,1); //一位数据发送完毕,时钟拉高
d<<=1; // d|ddddddd0 抛掉最高位,其余数据左移一位,最低位填0
}
}
void write_cmd_mini12864(unsigned char cmd) //写命令
{
digitalWrite(cs_mini12864,0); //片选拉低,选中芯片
digitalWrite(rs_mini12864,0); //rs为低,写入命令
send_8bit_mini12864(cmd); //写入8位命令
}
void write_dat_mini12864(unsigned char dat) //写数据
{
digitalWrite(cs_mini12864,0); //片选拉低,选中芯片
digitalWrite(rs_mini12864,1); //rs为高,写入数据
send_8bit_mini12864(dat); //写入8位数据
}
void mini12864_cl() //清屏,其实就是把所有的地址全部填成0
{
unsigned char x,y;
for(y=0;y<8;y++)
{
write_cmd_mini12864(0xb0+y);
write_cmd_mini12864(0x10);
write_cmd_mini12864(0x00);
for(x=0;x<132;x++) write_dat_mini12864(0);
}
}
void mini12864_Init() //初始化
{
pinMode(cs_mini12864,OUTPUT); //设置各个I/O为输出
pinMode(rst_mini12864,OUTPUT);
pinMode(rs_mini12864,OUTPUT);
pinMode(sck_mini12864,OUTPUT);
pinMode(sda_mini12864,OUTPUT);
digitalWrite(cs_mini12864,LOW);
digitalWrite(rst_mini12864,LOW); //物理重置
delay(200);
digitalWrite(rst_mini12864,HIGH);
delay(1000);
write_cmd_mini12864(0xe2); //软件重置
delay(200);
//以下为初始设置,具体请参考数据手册
write_cmd_mini12864(0x24);//对比度
write_cmd_mini12864(0x81);//SET ELECTRONIC VOLUME
write_cmd_mini12864(0x20);//set pm: 通过改变这里的数值来改变电压
write_cmd_mini12864(0x2f);//set power control
write_cmd_mini12864(0xa2);//BR=1/9
write_cmd_mini12864(0xa0);//set seg direction
write_cmd_mini12864(0xc8);//set com direction
write_cmd_mini12864(0x40);//set scroll line
//write_cmd(0xa6);//set inverse display a6 off, a7 on
//write_cmd(0xa4);//set all pixel on
write_cmd_mini12864(0xaf);//开显示
mini12864_cl(); //清屏
}
void mini12864_address(unsigned char page,unsigned char column)
{
digitalWrite(cs_mini12864,0); //片选拉低,选中芯片
column=column-1;
page=page-1;
write_cmd_mini12864(0xb0+page);
write_cmd_mini12864(((column>>4)&0x0f)+0x10);
write_cmd_mini12864(column&0x0f);
}
void full_dispaly()
{
int i,j;
for(i=0;i<8;i++)
{
digitalWrite(cs_mini12864,0); //片选拉低,选中芯片
mini12864_address(i+1,0);
for(j=0;j<128;j++)
{
write_dat_mini12864(0xff);
}
}
}
void disp_graphic_32X32(unsigned char page,unsigned char column,unsigned char *dp)
{
unsigned char i,j;
digitalWrite(cs_mini12864,0); //片选拉低,选中芯片
for(j=0;j<4;j++)
{
mini12864_address(page+1,column);
for(i=0;i<31;i++)
{
write_dat_mini12864(*dp);
dp++;
}
}
digitalWrite(cs_mini12864,1); //片选拉低,选中芯片
}
void display_graphic_16x16(unsigned char page,unsigned char column,unsigned char *dp)
{
unsigned char i,j;
digitalWrite(cs_mini12864,0); //片选拉低,选中芯片
for(j=0;j<2;j++)
{
mini12864_address(page+j,column);
for (i=0;i<16;i++)
{
write_dat_mini12864(*dp); /*写数据到LCD,每写完一个8 位的数据后列地址自动加1*/
dp++;
}
}
digitalWrite(cs_mini12864,1); //片选拉低,选中芯片
}
void display_graphic_8x16(unsigned char page,unsigned char column,unsigned char *dp)
{
unsigned char i,j;
digitalWrite(cs_mini12864,0); //片选拉低,选中芯片
for(j=0;j<2;j++)
{
mini12864_address(page+j,column);
for (i=0;i<8;i++)
{
write_dat_mini12864(*dp); /*写数据到LCD,每写完一个8 位的数据后列地址自动加1*/
dp++;
}
}
digitalWrite(cs_mini12864,1); //片选拉低,选中芯片
}
void setup()
{
mini12864_Init(); //初始化液晶
}
void loop()
{
full_dispaly();
delay(2000);
mini12864_cl(); //清屏
display_graphic_16x16(4,24,ao);
display_graphic_16x16(4,24+16,song);
display_graphic_16x16(4,24+32,ji);
display_graphic_16x16(4,24+48,qi);
display_graphic_16x16(4,24+64,ren);
delay(5000);
}
}
程序效果
程序下载到 Arduino 控制器之后就可以显示出汉字“奥松机器人”了。
[ Arduino LCD 12864液晶摇杆扩展板]
资料下载
- 产品资料
下载链接：https://pan.baidu.com/s/18udTC1NjktRBPCoumGFJ-g
提取码：ihq0
- 产品购买链接：http://www.alsrobot.cn/goods-744.html
- 奥松机器人技术论坛：http://www.makerspace.cn
